D-LoopĪ D-Loop surrounds the arrow at the string and is a point of connection for a mechanical archery release it is made or a short piece of cord fastened to the bow string by two knots. The cable, which is not only a key in the timing of the compound bow’s cams, but is also the cable predominantly used in setting a bow’s draw weight. Compound BowĪ compound bow is a modern bow that uses a levering system, usually of cables and cams, to bend the limbs before a shot is taken. On a Solo Cam bow, the cam will be attached to the bottom limb of the bow while an idler wheel will be attached to the top limb. They are attached at the end of the limbs and transfer the power of the limbs to the string and arrow during the shot. CamsĬams of a compound bow are round to oval metal discs which are held in place to the limbs via a pin and they are where the string and cable(s) terminate. The longer the ATA measurement, the smaller the cam lean the shorter the ATA the greater the cam lean. Cam LeanĬam lean on a compound bow refers to the amount the cam(s) are canted or tilted off the vertical alignment of the bow and is due to the cable(s) and or bow string being pulled to the cable guard. The Cable slide on a compound bow is a plastic piece which attaches to the cable guard and holds the string / cables out of the arrow’s line of fire. It is stationary and contains the string / cables out of the line of fire via rollers. The cable roller is a replacement of the cable guard / cable slide system and is found on many newer bows. The cable guard on a compound bow is the fiberglass rod which runs perpendicular from the riser towards the bowstring and works with cable slide to keep the cable(s) out of the arrow’s line of fire. The cables on a compound bow run from cam to cam and work with the cams during the execution of the shot. They are usually sold in 75, 85, 100 and 125 grain weights. Current broadheads are made of razor sharp surgical stainless steel and are either of a fixed blade design or a mechanical design. The first broadheads (arrow heads) were chiseled out of stone and have improved drastically throughout the centuries. Broadheadīroadheads are the cutting head attached to the end of the arrow. The average brace height is around 7 inches. Brace Heightīrace height on a compound bow is the measurement from the crotch of the grip to the bow string. On a “solo cam” system, the bow string’s ends both terminate at the bottom cam but travels around the top idler wheel. The Bow string is the string, on a compound bow, which terminates at the cams on a two cam system. Bow slings should be installed loosely so they do not add unneeded torque when the shot is fired. It provides a “catch” for an archer so they do not drop the compound bow after taking a shot. Bow SlingĪ compound bow wrist sling is installed in tandem with a stabiler. There are many varieties of presses on the market all of which should be only used by people with knowledge of that particular press. Bow PressĪ bow press is a mechanical press which flexes the compound bow by pressing the limbs to take tension off the bow string and cable(s) so maintenance work can be performed on a compound bow. It is standard to have your arrow centered on the center of the berger hole when setting up the bow. The Berger Hole is the tapped hole above the arrow shelf on a compound bow. The arrow rest is screwed into the berger hole from the outside of the riser. It involves, along with other essential form elements, the tightening of the back muscles while releasing the shot. Back Tensionīack tension is the technique used to make the most efficient shot in archery. This is a manufacturer’s provided spec measurement and for a bow to operate with maximum efficiency, the measurement should be at least within 3/16 of an inch. The axle to axle measurement on a compound bow is from the center of the Cam’s pin (axle) to center of cam pin (axle). It also protects the gripping hand from accidental injury. The arrow shelf on a compound bow is the horizontal shelf designed into the riser which contains the arrow in all stages of the shot. Models are either stationary while some mechanically “drop away” during the shot. The arrow rest is the unit that screwed into the riser via the berger hole on a compound bow and provides a catch for the arrow to rest on before and during the shot. Carbon is the popular choice among modern archers because of its straightness, durability, and weight to spine ratio. Made from aluminum, carbon or a combination of carbon and aluminum, the modern hunting arrow has came a long way from its wooden predecessor. Elements of proper form include, but are not limited to, proper stance, posture, grip, arm positioning, and proper shot execution with a compound bow. Having proper archery shooting form will allow you to deliver consistent, accurate results.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |